ZS is initialized
OBP CRC check: OK
Clearing TLB Entries
Initializing Tsunami Cache
Probing for RAM @ 0x06000000
Probing for RAM @ 0x04000000
Probing for RAM @ 0x02000000
Top RAM bank @ 0x02000000
Available Memory 0x04000000
Context Table allocated, Available Memory 0x03ffc000
RAMsize allocated, Available Memory 0x03fec000
Level 1 Table allocated, Available Memory 0x03febc00
Mapping RAM @ 0xffef0000
RAMbase --> RAMsize mapped, Available Memory 0x03feba00
Mapping ROM @ 0xffd00000
ROMbase --> ROMsize mapped, Available Memory 0x03feb800
Mapping ROM @ 0x00000000
0 --> ROMsize mapped, Available Memory 0x03feb500
Available Memory 0x03feb000
ttya initialized
Probing Memory Bank #0 32 Megabytes
Probing Memory Bank #1 32 Megabytes
Probing Memory Bank #2 Nothing there
Probing Memory Bank #3 Nothing there
Incorrect configuration checksum;
Setting NVRAM parameters to default values.
Setting diag-switch? NVRAM parameter to true
Probing /iommu@0,10000000/sbus@0,10001000 at 0,0 p9000
Probing /iommu@0,10000000/sbus@0,10001000 at 4,0 espdma esp sd st SUNW,bpp led
Probing /iommu@0,10000000/sbus@0,10001000 at 1,0 ts102
Probing /iommu@0,10000000/sbus@0,10001000 at 2,0 SUNW,DBRIs3
Probing /iommu@0,10000000/sbus@0,10001000 at 3,0 Nothing there
ZS is initialized
OBP CRC check: OK
Clearing TLB Entries
Initializing Tsunami Cache
Probing for RAM @ 0x06000000
Probing for RAM @ 0x04000000
Probing for RAM @ 0x02000000
Top RAM bank @ 0x02000000
Available Memory 0x04000000
Context Table allocated, Available Memory 0x03ffc000
RAMsize allocated, Available Memory 0x03fec000
Level 1 Table allocated, Available Memory 0x03febc00
Mapping RAM @ 0xffef0000
RAMbase --> RAMsize mapped, Available Memory 0x03feba00
Mapping ROM @ 0xffd00000
ROMbase --> ROMsize mapped, Available Memory 0x03feb800
Mapping ROM @ 0x00000000
0 --> ROMsize mapped, Available Memory 0x03feb500
Available Memory 0x03feb000
ttya initialized
Probing Memory Bank #0 32 Megabytes
Probing Memory Bank #1 32 Megabytes
Probing Memory Bank #2 Nothing there
Probing Memory Bank #3 Nothing there
Probing /iommu@0,10000000/sbus@0,10001000 at 0,0 p9000
Probing /iommu@0,10000000/sbus@0,10001000 at 4,0 espdma esp sd st SUNW,bpp led
Probing /iommu@0,10000000/sbus@0,10001000 at 1,0 ts102
Probing /iommu@0,10000000/sbus@0,10001000 at 2,0 SUNW,DBRIs3
Probing /iommu@0,10000000/sbus@0,10001000 at 3,0 Nothing there
Tadpole S3 SPARCbook, Keyboard Present
ROM Rev. 2.9 V1.00
64 MB memory installed, Serial #10690881.
Ethernet address 0:0:83:a3:21:41, Host ID: 80a32141.
Spinning discs down .. done
Boot device: /iommu/sbus/ledma@4,8400010/le@4,8c00000 File and args:
Automatic network cable selection succeeded : Using AUI Ethernet Interface
Type help for more information
ok boot /iommu/sbus/espdma@4,8400000/esp/sd@5,0 bsd
Boot device: /iommu/sbus/espdma@4,8400000/esp/sd@5,0 File and args: bsd
>> OpenBSD BOOT 2.3
Booting bsd @ 0x4000
3145804+437948 [52+149536+131969]
[ using 281932 bytes of bsd ELF symbol table ]
console is ttya
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2010 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 4.7 (GENERIC) #152: Fri Mar 19 02:33:48 MDT 2010
deraadt@sparc.openbsd.org:/usr/src/sys/arch/sparc/compile/GENERIC
real mem = 66699264 (63MB)
avail mem = 59355136 (56MB)
mainbus0 at root: Tadpole_S3
cpu0 at mainbus0: TMS390S10 @ 50 MHz, on-chip FPU
cpu0: physical 4K instruction (32 b/l), 2K data (16 b/l) cache enabled
obio0 at mainbus0
clock0 at obio0 addr 0x71200000: mk48t08 (eeprom)
timer0 at obio0 addr 0x71d00000 delay constant 23
zs0 at obio0 addr 0x71100000 pri 12, softpri 6
zstty0 at zs0 channel 0: console
zstty1 at zs0 channel 1
zs1 at obio0 addr 0x71000000 pri 12, softpri 6
zskbd0 at zs1 channel 0: keyboard, type 5, layout 0x2e
wskbd0 at zskbd0 mux 1
zsms0 at zs1 channel 1
wsmouse0 at zsms0 mux 0
slavioconfig at obio0 addr 0x71800000 not configured
auxreg0 at obio0 addr 0x71900000
auxreg1 at obio0 addr 0x71910000
tctrl0 at obio0 addr 0x42000020 pri 11
tctrl0: main power available, lid down
clk-ctrl at obio0 addr 0x713c0000 not configured
btcham0 at obio0 addr 0x71380000: id 0x3a, revision 0xa0
com0 at obio0 addr 0x713a0000 pri 13: ns16550a, 16 byte fifo
com0: probed fifo depth: 0 bytes
iommu0 at mainbus0 addr 0x10000000: version 0x1/0x4, page-size 4096, range 64MB
sbus0 at iommu0: clock = 25 MHz
"p9000" at sbus0 class display slot 0 offset 0x100000 not configured
dma0 at sbus0 slot 4 offset 0x8400000: rev 2
esp0 at dma0 offset 0x8800000 pri 4: ESP200, 40MHz
scsibus0 at esp0: 8 targets, initiator 7
probe(esp0:3:0): max sync rate 10.00MB/s
sd0 at scsibus0 targ 3 lun 0:SCSI2 0/direct fixed
sd0: drive offline
sd1 at scsibus0 targ 5 lun 0:SCSI2 0/direct d
sd1: 3067MB, 512 bytes/sec, 6281856 sec total
cd0 at scsibus0 targ 6 lun 0:SCSI2 5/cdrom reme
bpp0 at sbus0 slot 4 offset 0xc800000: DMA2
ledma0 at sbus0 slot 4 offset 0x8400010: rev 2
le0 at ledma0 offset 0x8c00000 pri 6: address 00:00:83:a3:21:41
le0: 16 receive buffers, 4 transmit buffers
tslot0 at sbus0 slot 1 offset 0x2000000 pri 11: 2 slots
pcmcia0 at tslot0 socket 0
pcmcia1 at tslot0 socket 1
"SUNW,DBRIs3" at sbus0 class ISDN slot 2 offset 0x40 not configured
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
bootpath: /iommu@0,10000000/sbus@0,10001000/espdma@4,8400000/esp@4,8800000/sd@50
root on sd1a swap on sd1b dump on sd1b
WARNING: / was not properly unmounted
Automatic boot in progress: starting file system checks.
/dev/rsd1a: 2695 files, 32121 used, 810934 free (78 frags, 101357 blocks, 0.0% )
/dev/rsd1a: MARKING FILE SYSTEM CLEAN
/dev/rsd1e: 9 files, 8 used, 164293 free (21 frags, 20534 blocks, 0.0% fragment)
/dev/rsd1e: MARKING FILE SYSTEM CLEAN
/dev/rsd1d: 22231 files, 288694 used, 569387 free (1787 frags, 70950 blocks, 0.)
/dev/rsd1d: MARKING FILE SYSTEM CLEAN
setting tty flags
pf enabled
starting network
starting system logger
starting initial daemons: ntpd.
savecore: no core dump
checking quotas: done.
building ps databases: kvm dev.
clearing /tmp
starting pre-securelevel daemons:.
setting kernel security level: kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
ssh-keygen: generating new DSA host key...
ssh-keygen: generating new RSA host key... done.
ssh-keygen: generating new RSA1 host key... done.
starting network daemons: sshd sendmail inetd.
starting local daemons:.
standard daemons: cron.
Thu Dec 31 12:09:33 GMT 1987
OpenBSD/sparc (tadpole.hecnet.eu) (console)
login:
Friday 13 August 2010
Successful install of OpenBSD 4.7 on a SPARCbook 3
Here is the proof:
Subscribe to:
Post Comments (Atom)
0 comments:
Post a Comment